##前言
隨便記錄一下吧！交換機以及路由的配置。
##eNSP模擬
首先我們搭建如下網絡拓?fù)?br>

PC機的配置

PC1
vlan10
ip : 192.168.10.1
默認網關：192.168.10.254

PC2
vlan20
ip : 192.168.20.1
默認網關：192.168.20.254

PC3
vlan10
ip : 192.168.10.2
默認網關：192.168.10.254

PC4
vlan20
ip : 192.168.20.2
默認網關：192.168.20.254

PC6
internet
ip : 192.168.100.1
默認網關: 192.168.100.254

PC8
vlan 10
ip : 192.168.10.3
默認網關: 192.168.10.254

交換機的配置

二層交換機

LSW1
vlan 10 20
interface GigabitEthernet 0/0/2
port link-type access
port default vlan 10
quit
interface GigabitEthernet 0/0/3
port link-type access
port default vlan 20
quit
interface GigabitEthernet 0/0/1
port link-type trunk
port trunk allow-pass vlan all
quit

LSW2
vlan 10 20
interface GigabitEthernet 0/0/1
port link-type access
port default vlan 10
quit
interface GigabitEthernet 0/0/2
port link-type access
port default vlan 20
quit
interface GigabitEthernet 0/0/3
port link-type trunk
port trunk allow-pass vlan all
quit

三層交換機

LSW3
vlan 10 20 200
interface GigabitEthernet 0/0/1
port link-type trunk
port trunk allow-pass vlan all
quit
interface GigabitEthernet 0/0/2
port link-type trunk
port trunk allow-pass vlan all
quit
interface GigabitEthernet 0/0/3
port link-type access
port default vlan 200
quit
interface Vlanif 200
ip address 192.168.200.1 24
quit
ip route-static 0.0.0.0 0.0.0.0 192.168.200.2
quit

路由器的配置

AR1
interface GigabitEthernet 0/0/0
ip address 192.168.200.2 24
quit
interface GigabitEthernet 0/0/1
ip address 192.168.100.254 24
quit
ip route-static 192.168.10.0 24 192.168.200.1
ip route-static 192.168.20.0 24 192.168.200.1

訪問控制列表ACL

首先我們可以查看AR2200的產品手冊

acl number 2000
rule 5 deny source 192.168.10.0 0.0.0.255
quit
acl number 2001
rule 5 permit source 192.168.20.0 0.0.0.255
quit
acl number 3001
rule 5 deny tcp source 192.168.200.0 0.0.0.255 destination 0.0.0.0 0 destination-port eq telnet
quit
interface GigabitEthernet 0/0/0
traffic-filter inbound acl 2001
quit
interface GigabitEthernet 0/0/1
traffic-filter inbound acl 3001
quit

常用的其他命令

display vlan 顯示Vlan
display ip routing-table 顯示路由表
display ip interface brief 顯示所有的接口
display acl all 顯示所有的acl表項
clear configuration interface GigabitEthernet 0/0/1
undo shutdown 開啟已關閉的接口

注意事項

一些sys,quit之類的命令可能不是很全，自己注意！
#總結
其實是一些比較簡單的東西，只是沒什么時間了解罷了！